Home > BRASS > C36000 > C36000 Solid Bar
We found 0 results matching your criteria.

C36000 Solid Bar / Rounds



Atlas carries C36000 Free Cutting Brass Solid Bar stock.We carry C36000 Solid Bar stock in a wide range of sizes and will cut the material to length. This alloy is ideally suited for high speed machining operations with its superior machinability, thread rolling and knurling characteristics. Its machinability rating of 100 is standard against which all other copper alloys are rated. It is easily soldered or brazed and has good resistance to corrosion.

___________________________________________________________________________________________







Diameter (inches) Part Number
0.0625 3600S-0.5
0.0781 3600S-0.6248
0.0930 3600S-0.744
0.0938 3600S-0.7504
0.1250 3600S-1
0.1875 3600S-1.5
0.2188 3600S-1.7504
0.2500 3600S-2
0.2656 3600S-2.1248
0.2813 3600S-2.2504
0.3125 3600S-2.5
0.3750 3600S-3
0.4375 3600S-3.5
0.5000 3600S-4
0.5625 3600S-4.5
0.6250 3600S-5
0.6875 3600S-5.5
0.7500 3600S-6
0.8125 3600S-6.5
0.8750 3600S-7
0.9375 3600S-7.5
1.0000 3600S-8
1.0625 3600S-8.5
1.1250 3600S-9
1.1875 3600S-9.5
1.2500 3600S-10
1.3125 3600S-10.5
1.3750 3600S-11
1.4375 3600S-11.5
1.5000 3600S-12
1.5625 3600S-12.5
1.6250 3600S-13
1.6875 3600S-13.5
1.7500 3600S-14
1.8125 3600S-14.5
1.8750 3600S-15
1.9375 3600S-15.5
2.0000 3600S-16
2.1250 3600S-17
2.1875 3600S-17.5
2.2500 3600S-18
2.3750 3600S-19
2.5000 3600S-20
2.6250 3600S-21
2.7500 3600S-22
2.8750 3600S-23
3.0000 3600S-24
3.1250 3600S-25
3.2500 3600S-26
3.3750 3600S-27
3.5000 3600S-28
3.7500 3600S-30
4.0000 3600S-32
4.2500 3600S-34
4.5000 3600S-36
4.7500 3600S-38
5.0000 3600S-40
5.2500 3600S-42
5.5000 3600S-44
5.7500 3600S-46
6.0000 3600S-48
6.5000 3600S-52
7.0000 3600S-56
7.5000 3600S-60
8.0000 3600S-64
8.5000 3600S-68
9.0000 3600S-72
9.5000 3600S-76
10.000 3600S-80
11.000 3600S-88
11.500 3600S-92
12.000 3600S-96


___________________________________________________________________________________________


TYPICAL USES

Some of the typical areas that C360000 is used in, is as follows: Faucet Components, Pneumatic Fittings, Fluid Connectors, Automatic Screw Machine Parts, Unions, Adapters, Screw Machine Products, Gauges, Valve Seats, Valve Trim, Valve Stems, Nozzles, Pinions, Gears



CHEMICAL COMPOSITION

(%max., unless shown as range or min.)
Cu Fe Pb Zn
Min./Max. 60.0-63.0 .35 2.5-3.0 Rem.
Nominal 61.5 - 2.7 35.4

Note: Cu + Sum of Named Elements, 99.5% min.



MECHANICAL PROPERTIES


(measured at room temperature, 68 F (20 C)
Temper Section
Size
Cold
Work
Typ/
Min
Temp Tensile
Strength
Yield
Strength
(0.5% ext.
under load)
Yield
Strength
(0.2%
offset)
Yield
Strength
(0.05%
offset)
El Rockwell
Hardness
Vickens
Hard.
Brinell
Hard.
Shear
Strength
Fatigue
Strength*
Izod
Impact
Strength

in. %
F ksi ksi ksi ksi % B C F 30T 500 500 3000 ksi ksi ft-lb

mm.

C MPa MPa MPa MPa







MPa MPa J
Rod
H04 0.375 0 TYP 68 - - - - - 78 - - - - - - 34 - 0.0

12.7

20 - - - - - 78 - - - - - - 234 - 0.0
H02 1.5 0 TYP 68 - - - - - 65 - - - - - - - - 0.0

38.1

20 - - - - - 65 - - - - - - - - 0.0
H04 0.625 0 SMIN 68 65 30 - - 6 - - - - - - - - - 0.0

15.9

20 450 205 - - 6 - - - - - - - - - 0.0
H02 3.0 0 SMIN 68 45 15 - - 20 - - - - - - - - - 0.0

76.2

20 310 105 - - 20 - - - - - - - - - 0.0
O60 1.5 0 SMIN 68 44 18 - - 20 - - - - - - - - - 0.0

38.1

20 305 18 - - 20 - - - - - - - - -