C95900 Aluminum Bronze Rectangle / Plate
Atlas Bronze offers C95900 Aluminum Bronze in
Solids and Rectangles.
This alloy
is available as both an Off-the-Shelf product and in special castings.
This is an excellent heavy duty bearing alloy. However, it does not tolerate misalignment or
dirty lubricants, and generally should be used against hardened steel
shafts, with both shaft and bearing machined to fine surface finishes.
__________________________________________________________________________________________
__________________________________________________________________________________________
TYPICALLY USED FOR:
This
material is used in a variety of applications. Typical uses for this
alloy are:
Bushings, High Strength Clamps, Gears, Valves, Bearings, Pawl, Valve
Bodies, Landing Gear Parts, Worm Gears, Machine Parts, Pressure Blocks
for the Steel Industry, Bearing Segments for the Steel Industry, Valve
Seats, Valve Guides, Pickling Hooks, Spur Gears, Heavily Loaded Worm
Gears, Pump Parts
CHEMICAL COMPOSITION:
Chemical Composition
(%max., unless shown as range or min.)
|
|
Cu
|
Al
|
Fe
|
Mn
|
Ni(1)
|
|
Min./Max.
|
Rem.
|
12.0-13.5
|
3.0-5.0
|
1.5
|
.50
|
|
Nominal
|
-
|
12.7
|
4.0
|
-
|
-
|
(1) Ni value includes Co.
Note: Cu + Sum of Named Elements, 99.5% min.
MECHANICAL PROPERTIES:
(measured at room temperature, 68 F (20 C)
|
Temper
|
Section
Size
|
Cold
Work
|
Typ/
Min
|
Temp
|
Tensile
Strength
|
Yield
Strength
(0.5% ext.
under load)
|
Yield
Strength
(0.2%
offset)
|
Yield
Strength
(0.05%
offset)
|
El
|
Rockwell
Hardness
|
Vickens
Hard.
|
Brinell
Hard.
|
Shear
Strength
|
Fatigue
Strength*
|
Izod
Impact
Strength
|
|
in.
|
%
|
|
F
|
ksi
|
ksi
|
ksi
|
ksi
|
%
|
B
|
C
|
F
|
30T
|
500
|
500
|
3000
|
ksi
|
ksi
|
ft-lb
|
|
mm.
|
|
|
C
|
MPa
|
MPa
|
MPa
|
MPa
|
|
|
|
|
|
|
|
|
MPa
|
MPa
|
J
|
|
As Centrifugal Cast
|
|
M02
|
0.0
|
0
|
SMIN
|
68
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
241
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
241
|
-
|
-
|
0.0
|
|
As Continuous Cast
|
|
M07
|
0.0
|
0
|
SMIN
|
68
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
241
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
241
|
-
|
-
|
0.0
|
|
As Sand Cast
|
|
M01
|
0.0
|
0
|
SMIN
|
68
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
241
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
241
|
-
|
-
|
0.0
|
*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.
APPLICABLE SPECIFICATIONS:
NOTE: Information courtesy of Copper.org
|
Product
|
Specification
|
|
Centrifugal
|
ASTM B271
|
|
Continuous
|
ASTM B505
|
|
Ingot
|
ASTM B30
|
|
Sand
|
ASTM B148
|
|
