C86300 Manganese Bronze Cored Bar
Atlas Bronze offers C86300 Manganese Bronze Cored Bars. C86300 Cored Bar
is available as Continuous Cast Bar Stock per ASTM B505, Centrifugal Castings per ASTM B271 and Sand Castings per ASTM B584.
The method in which the material is
cast will depend on your
size, specification and desired quantity.
Manganese bronze is not used in the commercial or consumer market; it is
found almost exclusively in the industrial sector. This is because of
the durability and toughness of manganese bronze. It is used to make
bushings, valve stems, hydraulic cylinder components and propellers. Its
primary use in industry means this bronze is typically sold in large
amounts, with a standard bar length of 144 inches or 12 feet.
__________________________________________________________________________________________
|
ID (inches)
|
OD (inches)
|
Part Number
|
|
0.500
|
1.500
|
8630C-8-12
|
|
0.500
|
2.000
|
8630C-8-16
|
|
0.500
|
2.500
|
8630C-8-20
|
|
0.500
|
3.000
|
8630C-8-24
|
|
0.500
|
4.000
|
8630C-8-32
|
|
1.500
|
2.000
|
8630C-12-16
|
|
2.000
|
2.250
|
8630C-16-18
|
|
2.000
|
2.500
|
8630C-16-20
|
|
2.000
|
2.750
|
8630C-16-22
|
|
2.000
|
3.000
|
8630C-16-24
|
|
2.000
|
3.500
|
8630C-16-28
|
|
2.000
|
4.000
|
8630C-16-32
|
|
2.000
|
5.000
|
8630C-16-40
|
|
2.000
|
6.000
|
8630C-16-48
|
|
2.500
|
3.000
|
8630C-20-24
|
|
2.500
|
3.500
|
8630C-20-28
|
|
2.500
|
4.500
|
8630C-20-36
|
|
3.000
|
3.500
|
8630C-24-28
|
|
3.000
|
4.000
|
8630C-24-32
|
|
3.000
|
5.000
|
8630C-24-40
|
|
3.000
|
5.500
|
8630C-24-44
|
3.500
|
4.250
|
8630C-28-34
|
|
3.500
|
4.750
|
8630C-28-38
|
|
3.500
|
5.500
|
8630C-28-44
|
|
3.500
|
7.000
|
8630C-28-56
|
|
4.000
|
4.500
|
8630C-32-36
|
|
4.000
|
5.000
|
8630C-32-40
|
|
4.000
|
6.000
|
8630C-32-48
|
|
4.000
|
6.250
|
8630C-32-50
|
|
4.500
|
6.000
|
8630C-36-48
|
|
5.000
|
6.000
|
8630C-40-48
|
|
5.000
|
7.000
|
8630C-40-56
|
|
8.000
|
9.500
|
8630C-64-76
|
|
8.500
|
10.00
|
8630C-68-80
|
__________________________________________________________________________________________
TYPICALLY USED FOR:
This
material is used in a variety of applications. Typical uses for this
alloy are: Extra heavy duty, high strength alloy. Large valve stems, gears, cams,
slow-speed heavy-load bearings, screwdown nuts hydraulic cylinder parts.
CHEMICAL COMPOSITION:
(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
|
|
Cu(1)
|
Al
|
Fe
|
Pb
|
Mn
|
Ni(2)
|
Sn
|
Zn
|
|
Min./Max.
|
60.0-66.0
|
5.0-7.5
|
2.0-4.0
|
.20
|
2.5-5.0
|
1.0
|
.20
|
22.0-28.0
|
|
Nominal
|
63.0
|
6.2
|
3.0
|
-
|
3.7
|
-
|
-
|
25.0
|
(1) In determining Cu min., Cu may be calculated as Cu + Ni.
(2) Ni value includes Co.
Note: Cu + Sum of Named Elements, 99.0% min.
MECHANICAL PROPERTIES:
NOTE: Information courtesy of Copper.org
|
Temper
|
Section
Size
|
Cold
Work
|
Typ/
Min
|
Temp
|
Tensile
Strength
|
Yield
Strength
(0.5% ext.
under load)
|
Yield
Strength
(0.2%
offset)
|
Yield
Strength
(0.05%
offset)
|
El
|
Rockwell
Hardness
|
Vickens
Hard.
|
Brinell
Hard.
|
Shear
Strength
|
Fatigue
Strength*
|
Izod
Impact
Strength
|
|
in.
|
%
|
|
F
|
ksi
|
ksi
|
ksi
|
ksi
|
%
|
B
|
C
|
F
|
30T
|
500
|
500
|
3000
|
ksi
|
ksi
|
ft-lb
|
|
mm.
|
|
|
C
|
MPa
|
MPa
|
MPa
|
MPa
|
|
|
|
|
|
|
|
|
MPa
|
MPa
|
J
|
|
As Sand Cast
|
|
M01
|
0.0
|
0
|
TYP
|
68
|
119
|
62
|
-
|
-
|
18
|
-
|
-
|
-
|
-
|
-
|
-
|
225
|
-
|
25
|
15.0
|
|
0.0
|
|
|
20
|
821
|
427
|
-
|
-
|
18
|
-
|
-
|
-
|
-
|
-
|
-
|
225
|
-
|
172
|
20.0
|
|
As Centrifugal Cast
|
|
M02
|
0.0
|
0
|
SMIN
|
68
|
110
|
60
|
-
|
-
|
12
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
758
|
414
|
-
|
-
|
12
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
As Continuous Cast
|
|
M07
|
0.0
|
0
|
SMIN
|
68
|
110
|
62
|
-
|
-
|
14
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
-
|
0.0
|
|
0.0
|
|
|
20
|
758</ |
|
|
|
