Home > BRONZE > Bronze - Cast Alloys > C95400 > C95400 Rectangle / Plate
We found 0 results matching your criteria.

C95400 Aluminum Bronze Rectangle / Plate

Atlas Bronze offers
C95400 Aluminum Bronze, 9C in Rectangles & Plate, Solids, Tubes, Cored Bar, and Made to Order Castings.
This alloy is available as both an Off-the-Shelf product and in special castings. This product is also offered as a specialty product - LARGE BLOCK PLATE, sizes up to 10" thick x 18" wide . The method in which the material is cast will depend on your size, specification and desired quantity.

This material is used in a variety of applications. Typical uses for this alloy are: Bushings, High Strength Clamps, Gears, Valves, Bearings, Pawl, Valve Bodies, Landing Gear Parts, Worm Gears, Machine Parts, Pressure Blocks for the Steel Industry, Bearing Segments for the Steel Industry, Valve Seats, Valve Guides, Pickling Hooks, Spur Gears, Heavily Loaded Worm Gears, Pump Parts
__________________________________________________________________________________________






__________________________________________________________________________________________



TYPICALLY USED FOR:


This material is used in a variety of applications. Typical uses for this alloy are: Bushings, High Strength Clamps, Gears, Valves, Bearings, Pawl, Valve Bodies, Landing Gear Parts, Worm Gears, Machine Parts, Pressure Blocks for the Steel Industry, Bearing Segments for the Steel Industry, Valve Seats, Valve Guides, Pickling Hooks, Spur Gears, Heavily Loaded Worm Gears, Pump Parts



CHEMICAL COMPOSITION:

(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
Cu Al Fe Mn Ni(1)
Min./Max. 83.0 min 10.0-11.5 3.0-5.0 .50 1.5
Nominal 83.2 10.8 4.0 - -

(1) Ni value includes Co.
Note: Cu + Sum of Named Elements, 99.5% min.



MECHANICAL PROPERTIES:

(measured at room temperature, 68 F (20 C)
NOTE: Information courtesy of Copper.org
Temper Section
Size
Cold
Work
Typ/
Min
Temp Tensile
Strength
Yield
Strength
(0.5% ext.
under load)
Yield
Strength
(0.2%
offset)
Yield
Strength
(0.05%
offset)
El Rockwell
Hardness
Vickens
Hard.
Brinell
Hard.
Shear
Strength
Fatigue
Strength*
Izod
Impact
Strength

in. %
F ksi ksi ksi ksi % B C F 30T 500 500 3000 ksi ksi ft-lb

mm.

C MPa MPa MPa MPa







MPa MPa J
As Sand Cast
M01 0.0 0 TYP 68 85 35 - - 18 - - - - - - 170 47 28 16.0

0.0

20 586 241 - - 18 - - - - - - 170 324 193 22.0
As Centrifugal Cast
TQ50 0.0 0 SMIN 68 90 45 - - 6 - - - - - - 190 - - 0.0

0.0

20 620 310 - - 6 - - - - - - 190 - - 0.0
M02 0.0 0 SMIN 68 75 30 - - 12 - - - - - - 150 - - 0.0

0.0

20 515 205 - - 12 - - - - - - 150 - - 0.0
As Continuous Cast
TQ50 0.0 0 SMIN 68 95 45 - - 10 - - - - - - - - - 0.0

0.0

20 655 310 - - 10 - - - - - - - - - 0.0
M07 0.0 0 SMIN 68 85 32 - - 12 - - - - - - - - - 0.0

0.0

20 586 221 - - 12 - - - - - - - - - 0.0
As Permanent Mold Cast
M05 0.0 0 SMIN 68 100 40 - - 10 - - - - - - - - - 0.0

0.0

20 690 275 - - 10 - - - - - - - - - 0.0
As Sand Cast
TQ50 0.0 0 TYP 68 105 54 - - 8 - - - - - - 195 50 35 11.0

0.0

20 724 372 - - 8 -