Atlas Bronze offers C95500 Aluminum Bronze in
Solids and Made to Order Castings. Atlas stocks a select variety
of sizes in Rounds and various sizes on a Made to Order basis. Please note that the method in which the material
is
cast will depend on your size, specification and desired quantity.
__________________________________________________________________________________________
Click on the below image to select your size:
 
__________________________________________________________________________________________
TYPICALLY USED FOR:
This
material is used in a variety of applications. Typical uses for this
alloy are: Machine Parts, Glass Molds, Welding Jaws, Wear Plates, Air Craft
Components, Pickling Equipment, Valve Guides, Piston Guides, Valve
Seats, Pump Fluid Ends, Glands, Worms, Worms Wheels, Hot Mill Guides,
Landing Gear Parts, Sewage Treatment Applications, Valve Components,
Bearings, Gears, Bushings, Valve Bodies, Landing Gear Parts, Hand Gun
Recoil Mechanisms
CHEMICAL COMPOSITION:
(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
| |
Cu | Al | Fe | Mn | Ni(1) |
|---|
| Min./Max. | 78.0 min | 10.0-11.5 | 3.0-5.0 | 3.5 | 3.0-5.5 | | Nominal | 80.0 | 11.0 | 4.0 | - | 4.3 |
(1) Ni value includes Co.
Note: Cu + Sum of Named Elements, 99.5% min.
MECHANICAL PROPERTIES:
(measured at room temperature, 68 F (20 C)
NOTE: Information courtesy of Copper.org
| Temper |
Section
Size |
Cold
Work |
Typ/
Min |
Temp |
Tensile
Strength |
Yield
Strength
(0.5% ext.
under load) |
Yield
Strength
(0.2%
offset) |
Yield
Strength
(0.05%
offset) |
El |
Rockwell
Hardness |
Vickens
Hard. |
Brinell
Hard. |
Shear
Strength |
Fatigue
Strength* |
Izod
Impact
Strength |
|---|
| in. |
% |
| F |
ksi |
ksi |
ksi |
ksi |
% |
B |
C |
F |
30T |
500 |
500 |
3000 |
ksi |
ksi |
ft-lb |
| mm. |
|
| C |
MPa |
MPa |
MPa |
MPa |
|
|
|
|
|
|
|
|
MPa |
MPa |
J |
| As Sand Cast | | M01 | 0.0 | 0 | TYP | 68 | 100 | 44 | - | - | 12 | 87 | - | - | - | - | - | 195 | 48 | 31 | 13.0 |
| 0.0 |
|
| 20 | 689 | 303 | - | - | 12 | 87 | - | - | - | - | - | 195 | 331 | 214 | 18.0 | | As Centrifugal Cast | | TQ50 | 0.0 | 0 | SMIN | 68 | 110 | 60 | - | - | 5 | - | - | - | - | - | - | 200 | - | - | 0.0 |
| 0.0 |
|
| 20 | 760 | 415 | - | - | 5 | - | - | - | - | - | - | 200 | - | - | 0.0 | | M02 | 0.0 | 0 | SMIN | 68 | 90 | 40 | - | - | 6 | - | - | - | - | - | - | 190 | - | - | 0.0 |
| 0.0 |
|
| 20 | 620 | 275 | - | - | 6 | - | - | - | - | - | - | 190 | - | - | 0.0 | | As Continuous Cast | | TQ50 | 0.0 | 0 | SMIN | 68 | 110 | 62 | - | - | 8 | - | - | - | - | - | - | - | - | - | 0.0 |
| 0.0 |
|
| 20 | 758 | 427 | - | - | 8 | - | - | - | - | - | - | - | - | - | 0.0 | | M07 | 0.0 | 0 | SMIN | 68 | 95 | 42 | - | - | 10 | - | - | - | - | - | - | - | - | - | 0.0 |
| 0.0 |
|
| 20 | 655 | 290 | - | - | 10 | - | - | - | - | - | - | - | - | - | 0.0 | | As Permanent Mold Cast | | M05 | 0.0 | 0 | SMIN | 68 | 110 | 60 | - | - | 5 | - | - | - | - | - | - | - | - | - | 0.0 |
| 0.0 |
|
| 20 | 760 | 415 | - | - | 5 | - | - | - | - | - | - | - | - | - | 0.0 | | As Sand Cast | | TQ50 | 0.0 | 0 | TYP | 68 | 120 | 68 | - | - | 10 | - | - | - | - | - | - | 230 | 70 | 38 | 15.0 |
| 0.0 |
|
| 20 | 827 | 469 | - | - | 10 | - | - | - | - | - | - | 230 | 483 | 262 | 20.0 | | M01 | 0.0 | 0 | SMIN | 68 | 90 | 40 | - | - | 6 | - | - | - | - | - | - | 190 | - | - | 0.0 |
| 0.0 |
|
| 20 | 620 | 275 | - | - | 6 | - | - | - | - | - | - | 190 | - | - | 0.0 | | TQ50 | 0.0 | 0 | SMIN | 68 | 110 | 60 | - | - | 5 | - | - | - | - | - | - | 200 | - | - | 0.0 |
| 0.0 |
|
| 20 | 760 | 415 | - | - | 5 | - | - | - | - | - | - | 200 | - | - | 0.0 |
*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.
APPLICABLE SPECIFICATIONS:
NOTE: Information courtesy of Copper.org
| Product | Specification |
| Centrifugal | ASTM B271
SAE J462, J461 | | Continuous | ASTM B505
SAE J461, J462 | | Ingot | ASTM B30 | | Precision | ASTM B806 | | Sand | ASTM B148, B763
SAE J461, J462 |
|
