Atlas Bronze offers C95400 Aluminum Bronze, 9C in
Solids, Tubes, Cored Bar, Plate, Rectangles and Castings.
This alloy
is available as both an Off-the-Shelf product and in special castings.
This product is also offered as a specialty product - LARGE BLOCK PLATE, sizes up to 10" thick x 18" wide . The method in which the material is
cast will depend on your size, specification and desired quantity.
__________________________________________________________________________________________
Click on the below image to select your size:
 
__________________________________________________________________________________________
TYPICALLY USED FOR:
This
material is used in a variety of applications. Typical uses for this
alloy are: Bushings, High Strength Clamps, Gears, Valves, Bearings, Pawl, Valve
Bodies, Landing Gear Parts, Worm Gears, Machine Parts, Pressure Blocks
for the Steel Industry, Bearing Segments for the Steel Industry, Valve
Seats, Valve Guides, Pickling Hooks, Spur Gears, Heavily Loaded Worm
Gears, Pump Parts
CHEMICAL COMPOSITION:
(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
| |
Cu | Al | Fe | Mn | Ni(1) |
|---|
| Min./Max. | 83.0 min | 10.0-11.5 | 3.0-5.0 | .50 | 1.5 | | Nominal | 83.2 | 10.8 | 4.0 | - | - |
(1) Ni value includes Co.
Note: Cu + Sum of Named Elements, 99.5% min.
MECHANICAL PROPERTIES:
(measured at room temperature, 68 F (20 C)
NOTE: Information courtesy of Copper.org
| Temper |
Section
Size |
Cold
Work |
Typ/
Min |
Temp |
Tensile
Strength |
Yield
Strength
(0.5% ext.
under load) |
Yield
Strength
(0.2%
offset) |
Yield
Strength
(0.05%
offset) |
El |
Rockwell
Hardness |
Vickens
Hard. |
Brinell
Hard. |
Shear
Strength |
Fatigue
Strength* |
Izod
Impact
Strength |
|---|
| in. |
% |
| F |
ksi |
ksi |
ksi |
ksi |
% |
B |
C |
F |
30T |
500 |
500 |
3000 |
ksi |
ksi |
ft-lb |
| mm. |
|
| C |
MPa |
MPa |
MPa |
MPa |
|
|
|
|
|
|
|
|
MPa |
MPa |
J |
| As Sand Cast | | M01 | 0.0 | 0 | TYP | 68 | 85 | 35 | - | - | 18 | - | - | - | - | - | - | 170 | 47 | 28 | 16.0 |
| 0.0 |
|
| 20 | 586 | 241 | - | - | 18 | - | - | - | - | - | - | 170 | 324 | 193 | 22.0 | | As Centrifugal Cast | | TQ50 | 0.0 | 0 | SMIN | 68 | 90 | 45 | - | - | 6 | - | - | - | - | - | - | 190 | - | - | 0.0 |
| 0.0 |
|
| 20 | 620 | 310 | - | - | 6 | - | - | - | - | - | - | 190 | - | - | 0.0 | | M02 | 0.0 | 0 | SMIN | 68 | 75 | 30 | - | - | 12 | - | - | - | - | - | - | 150 | - | - | 0.0 |
| 0.0 |
|
| 20 | 515 | 205 | - | - | 12 | - | - | - | - | - | - | 150 | - | - | 0.0 | | As Continuous Cast | | TQ50 | 0.0 | 0 | SMIN | 68 | 95 | 45 | - | - | 10 | - | - | - | - | - | - | - | - | - | 0.0 |
| 0.0 |
|
| 20 | 655 | 310 | - | - | 10 | - | - | - | - | - | - | - | - | - | 0.0 | | M07 | 0.0 | 0 | SMIN | 68 | 85 | 32 | - | - | 12 | - | - | - | - | - | - | - | - | - | 0.0 |
| 0.0 |
|
| 20 | 586 | 221 | - | - | 12 | - | - | - | - | - | - | - | - | - | 0.0 | | As Permanent Mold Cast | | M05 | 0.0 | 0 | SMIN | 68 | 100 | 40 | - | - | 10 | - | - | - | - | - | - | - | - | - | 0.0 |
| 0.0 |
|
| 20 | 690 | 275 | - | - | 10 | - | - | - | - | - | - | - | - | - | 0.0 | | As Sand Cast | | TQ50 | 0.0 | 0 | TYP | 68 | 105 | 54 | - | - | 8 | - | - | - | - | - | - | 195 | 50 | 35 | 11.0 |
| 0.0 |
|
| 20 | 724 | 372 | - | - | 8 | - | - | - | - | - | - | 195 | 345 | 241 | 15.0 | | M01 | 0.0 | 0 | SMIN | 68 | 75 | 30 | - | - | 12 | - | - | - | - | - | - | 150 | - | - | 0.0 |
| 0.0 |
|
| 20 | 517 | 207 | - | - | 12 | - | - | - | - | - | - | 150 | - | - | 0.0 | | M01 | 0.0 | 0 | SMIN | 68 | 75 | 30 | - | - | 12 | - | - | - | - | - | - | 150 | - | - | 0.0 |
| 0.0 |
|
| 20 | 515 | 205 | - | - | 12 | - | - | - | - | - | - | 150 | - | - | 0.0 | | M01 | 0.0 | 0 | SMIN | 68 | 75 | 30 | - | - | - | - | - | - | - | - | - | - | - | - | 0.0 |
| 0.0 |
|
| 20 | 517 | 207 | - | - | - | - | - | - | - | - | - | - | - | - | 0.0 | | As Permanent Mold Cast | | M05 | 0.0 | 0 | TYP | 68 | 105 | 46 | - | - | 11 | - | - | - | - | - | - | - | - | - | 0.0 |
| 0.0 |
|
| 20 | 725 | 320 | - | - | 11 | - | - | - | - | - | - | - | - | - | 0.0 | | As Sand Cast | | TQ50 | 0.0 | 0 | MIN | 68 | 90 | 45 | - | - | 6 | - | - | - | - | - | - | 190 | - | - | 0.0 |
| 0.0 |
|
| 20 | 620 | 310 | - | - | 6 | - | - | - | - | - | - | 190 | - | - | 0.0 | | TQ50 | 0.0 | 0 | SMIN | 68 | 90 | 45 | - | - | 6 | - | - | - | - | - | - | 190 | - | - | 0.0 |
| 0.0 |
|
| 20 | 621 | 310 | - | - | 6 | - | - | - | - | - | - | 190 | - | - | 0.0 |
*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.
APPLICABLE SPECIFICATIONS:
NOTE: Information courtesy of Copper.org
| Product | Specification |
| Centrifugal | ASME SB271
ASTM B271
SAE J461, J462 | | Continuous | ASTM B505
SAE J461, J462 | | Ingot | ASTM B30 | | Permanent | ASTM B806 | | Precision | MILITARY MIL-C-11866 | | Sand | ASME SB148
ASTM B66, B148, B763
SAE J461, J462 |
|
