Home > BRONZE > Bronze - Cast Alloys > C93200 > C93200 Solid Bar
We found 0 results matching your criteria.

C93200 Bearing Bronze Solid Bar

Atlas Bronze offers
C93200 Bearing Bronze, SAE 660 Solid Bar stock. CDA 932 Bearing Bronze Solid Bar is stocked in both full bar length of 105" long or can be cut to exact desired length.


This material is used in a variety of Bearing / Bushing applications. Typical uses for this alloy are:
Fuel Pump Bushings, Water Pump Bushings, Diesel Engine Wrist Pin Bushings, Hydraulic Press Stuffing Box, Insert Bearings, Bearings, Thrust Washers, Pumps, Bushings, Machine Parts, Pump Impellers, General Purpose Bushings, Fittings, Pump Fixtures, Machine Tool Bearings.


__________________________________________________________________________________________






DIAMETER (inches)PART NUMBER
.3750"
9320S-3
.5000"9320S-4
.6250"9320S-5
.7500"9320S-6
.8750"9320S-7
1.000"9320S-8
1.125"9320S-9
1.250"9320S-10
1.375"9320S-11
1.500"9320S-12
1.625"9320S-13
1.750"9320S-14
1.875"9320S-15
2.000"9320S-16
2.125"9320S-17
2.250"9320S-18
2.375"9320S-19
2.500"9320S-20
2.625"9320S-21
2.750"9320S-22
3.000"9320S-24
3.250"9320S-26
3.500"9320S-28
3.750"9320S-30
4.000"9320S-32
4.250"9320S-34
4.500"9320S-36
4.750"9320S-38
5.000"9320S-40
5.250"9320S-42
5.500"9320S-44
5.750"9320S-46
6.000"9320S-48
6.500"9320S-52
7.000"9320S-56
7.500"9320S-60
8.000"9320S-64
8.500"9320S-68
9.000"9320S-72
9.500"9320S-76
10.00"9320S-80
10.50"9320S-84
11.00"9320S-88
12.00"9320S-96
12.50"9320S-100
13.00"9320S-104
14.00"9320S-112
15.00"9320S-120
16.00"
9320S-128


__________________________________________________________________________________________



TYPICALLY USED FOR:


This material is used in a variety of applications. Typical uses for this alloy are: Fuel Pump Bushings, Water Pump Bushings, Diesel Engine Wrist Pin Bushings, Hydraulic Press Stuffing Box, Insert Bearings, Bearings, Thrust Washers, Pumps, Bushings, Machine Parts, Pump Impellers, General Purpose Bushings, Fittings, Pump Fixtures, Machine Tool Bearings.



CHEMICAL COMPOSITION:

(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
Cu(1)AlSbFePbNi(2)P(3)SiSSnZn
Min./Max.81.0-85.0.005.35.206.0-8.01.0.15.005.086.3-7.51.0-4.0
Nominal83.0---7.0----6.92.5

(1) In determining Cu min., Cu may be calculated as Cu + Ni.
(2) Ni value includes Co.
(3) For continuous castings, P shall be 1.5%, max.
Note: Cu + Sum of Named Elements, 99.0% min.



MECHANICAL PROPERTIES:

(measured at room temperature, 68 F (20 C)
NOTE: Information courtesy of Copper.org
Temper Section
Size
Cold
Work
Typ/
Min
Temp Tensile
Strength
Yield
Strength
(0.5% ext.
under load)
Yield
Strength
(0.2%
offset)
Yield
Strength
(0.05%
offset)
El Rockwell
Hardness
Vickens
Hard.
Brinell
Hard.
Shear
Strength
Fatigue
Strength*
Izod
Impact
Strength

in. %
F ksi ksi ksi ksi % B C F 30T 500 500 3000 ks