Home > ALLOYS > Bronze - Cast Alloys > C93200 > C93200 Big Block Plate

C93200 Bearing Bronze Big Block Plate

Atlas Bronze offers C93200 Bearing Bronze Big Block Plate per ASTM B505. CDA 932 Bearing Bronze Plate is available as Continuous Cast Bar Stock dual certified ASTM B505. We also offer a select number of sizes in Sand Casting (ASTM B584) as well. *The method in which the material is cast will depend on your size, specification, and desired quantity.*

Our C93200 Bearing Bronze per ASTM B505 is available in Standard thicknesses or we can cut your desired thickness, width and length from one of our Big Blocks! We regularly stock our C93200 Big Block Plates in a variety of sizes to achieve optimal cutting capacity:

  • 4" thick x 15" wide
  • 5" thick x 15" wide
  • 8" thick x 18" wide
  • 10" thick x 12" wide











TYPICALLY USED FOR:


This material is used in a variety of applications. Typical uses for this alloy are: Fuel Pump Bushings, Water Pump Bushings, Diesel Engine Wrist Pin Bushings, Hydraulic Press Stuffing Box, Insert Bearings, Bearings, Thrust Washers, Pumps, Bushings, Machine Parts, Pump Impellers, General Purpose Bushings, Fittings, Pump Fixtures, Machine Tool Bearings.


CHEMICAL COMPOSITION:

(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
Cu(1) Al Sb Fe Pb Ni(2) P(3) Si S Sn Zn
Min./Max. 81.0-85.0 .005 .35 .20 6.0-8.0 1.0 .15 .005 .08 6.3-7.5 1.0-4.0
Nominal 83.0 - - - 7.0 - - - - 6.9 2.5

(1) In determining Cu min., Cu may be calculated as Cu + Ni.
(2) Ni value includes Co.
(3) For continuous castings, P shall be 1.5%, max.
Note: Cu + Sum of Named Elements, 99.0% min.



MECHANICAL PROPERTIES:

(measured at room temperature, 68 F (20 C)
NOTE: Information courtesy of Copper.org
Temper Section
Size
Cold
Work
Typ/
Min
Temp Tensile
Strength
Yield
Strength
(0.5% ext.
under load)
Yield
Strength
(0.2%
offset)
Yield
Strength
(0.05%
offset)
El Rockwell
Hardness
Vickens
Hard.
Brinell
Hard.
Shear
Strength
Fatigue
Strength*
Izod
Impact
Strength

in. %
F ksi ksi ksi ksi % B C F 30T 500 500 3000 ksi ksi ft-lb

mm.

C MPa MPa MPa MPa







MPa MPa J
As Sand Cast
M01 0.0 0 TYP 68 35 18 - - 20 - - - - - 65 - - 16 6.0

0.0

20 241 124 - - 20 - - - - - 65 - - 110 8.0
As Centrifugal Cast
M02 0.0 0 SMIN 68 30 14 - - 15 - - - - - - - - - 0.0

0.0

20 207 97 - - 15 - - - - - - - - - 0.0
As Continuous Cast
M07 0.0 0 SMIN 68 35 20 - - 10 - - - - - - - - - 0.0

0.0

20 241 138 - - 10 - - - - - - - - - 0.0
As Sand Cast
M01 0.0 0 SMIN 68 30 14 - - 15 - - - - - - - - - 0.0

0.0

20 207 97 - - 15 - - - - - - - - - 0.0

*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.



APPLICABLE SPECIFICATIONS:

NOTE: Information courtesy of Copper.org
Product Specification
Centrifugal ASTM B271
SAE J462, J461
Continuous ASTM B505
SAE J461, J462
Ingot ASTM B30
Permanent Mold SAE J461, J462
Sand ASTM B584, B763, B66
SAE J462, J461