Home > ALLOYS > Bronze - Cast Alloys > C93200 > C93200 Rectangle / Plate

C93200 Rectangle / Plate

Atlas Bronze offers C93200 Bearing Bronze, SAE 660 Rectangle / Plate stock. CDA 932 Bearing Bronze Rectangle / Plate Bar is stocked in both full bar length of 105" long or can be cut to exact desired width and length.

This material is used in a variety of Bearing / Bushing applications. Typical uses for this alloy are:

  • Fuel Pump Bushings
  • Water Pump Bushings
  • Diesel Engine Wrist Pin Bushings
  • Hydraulic Press
  • Stuffing Box
  • Insert Bearings
  • Bearings
  • Thrust Washers
  • Pumps
  • Bushings
  • Machine Parts
  • Pump Impellers
  • General Purpose Bushings
  • Fittings
  • Pump Fixtures
  • Machine Tool Bearings








TYPICALLY USED FOR:


This material is used in a variety of applications. Typical uses for this alloy are: Fuel Pump Bushings, Water Pump Bushings, Diesel Engine Wrist Pin Bushings, Hydraulic Press Stuffing Box, Insert Bearings, Bearings, Thrust Washers, Pumps, Bushings, Machine Parts, Pump Impellers, General Purpose Bushings, Fittings, Pump Fixtures, Machine Tool Bearings.



CHEMICAL COMPOSITION:

(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
Cu(1) Al Sb Fe Pb Ni(2) P(3) Si S Sn Zn
Min./Max. 81.0-85.0 .005 .35 .20 6.0-8.0 1.0 .15 .005 .08 6.3-7.5 1.0-4.0
Nominal 83.0 - - - 7.0 - - - - 6.9 2.5

(1) In determining Cu min., Cu may be calculated as Cu + Ni.
(2) Ni value includes Co.
(3) For continuous castings, P shall be 1.5%, max.
Note: Cu + Sum of Named Elements, 99.0% min.



MECHANICAL PROPERTIES:

(measured at room temperature, 68 F (20 C)
NOTE: Information courtesy of Copper.org
Temper Section
Size
Cold
Work
Typ/
Min
Temp Tensile
Strength
Yield
Strength
(0.5% ext.
under load)
Yield
Strength
(0.2%
offset)
Yield
Strength
(0.05%
offset)
El Rockwell
Hardness
Vickens
Hard.
Brinell
Hard.
Shear
Strength
Fatigue
Strength*
Izod
Impact
Strength

in. %
F ksi ksi ksi ksi % B C F 30T 500 500 3000 ksi ksi ft-lb

mm.

C MPa MPa MPa MPa







MPa MPa J
As Sand Cast
M01 0.0 0 TYP 68 35 18 - - 20 - - - - - 65 - - 16 6.0

0.0

20 241 124 - - 20 - - - - - 65 - - 110 8.0
As Centrifugal Cast
M02 0.0 0 SMIN 68 30 14 - - 15 - - - - - - - - - 0.0

0.0

20 207 97 - - 15 - - - - - - - - - 0.0
As Continuous Cast
M07 0.0 0 SMIN 68 35 20 - - 10 - - - - - - - - - 0.0

0.0

20 241 138 - - 10 - - - - - - - - - 0.0
As Sand Cast
M01 0.0 0 SMIN 68 30 14 - - 15 - - - - - - - - - 0.0

0.0

20 207 97 - - 15 - - - - - - - - - 0.0

*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.



APPLICABLE SPECIFICATIONS:

NOTE: Information courtesy of Copper.org
Product Specification
Centrifugal ASTM B271
SAE J462, J461
Continuous ASTM B505
SAE J461, J462
Ingot ASTM B30
Permanent Mold SAE J461, J462
Sand ASTM B584, B763, B66
SAE J462, J461