Home > BRONZE > Bronze - Cast Alloys > C90300 > C90300 Solid Bar
We found 0 results matching your criteria.

C90300 Navy Bronze Solid Bar

Atlas Bronze offers
C90300 Navy Bronze G Solid Bar stock. Atlas Bronze stocks Solid Bar stock in full bar lengths or we will cut the bars to your exact length.
This material is used in a variety of applications. Typical uses for this alloy are: Bearings and bushings, pump impellers, position rings, valve components, seal rings, steam fittings, gears.

_________________________________________________________________________________________






Available in the following sizes:

1.000" diameter - PART# 9030S-8
1.500" diameter - PART# 9030S-12
2.000" diameter - PART# 9030S-16
2.500" diameter - PART# 9030S-20
3.000" diameter - PART# 9030S-24
3.500" diameter - PART# 9030S-28
4.000" diameter - PART# 9030S-32
4.500" diameter - PART# 9030S-36
5.000" diameter - PART# 9030S-40
6.000" diameter - PART# 9030S-48


__________________________________________________________________________________________


TYPICALLY USED FOR:

This material is used in a variety of applications. Typical uses for this alloy are: Bearings and bushings, pump impellers, position rings, valve components, seal rings, steam fittings, gears .


CHEMICAL COMPOSITION:

(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
Cu(1)AlSbFePbNi(2)P(3)SiSSnZn
Min./Max.86.0-89.0.005.20.20.301.0.05.005.057.5-9.03.0-5.0
Nominal87.5--------8.34.0

(1) In determining Cu min., Cu may be calculated as Cu + Ni.
(2) Ni value includes Co.
(3) For continuous castings, P shall be 1.5%, max.
Note: Cu + Sum of Named Elements, 99.4% min.



MECHANICAL PROPERTIES:

NOTE: Information courtesy of Copper.org
Temper Section
Size
Cold
Work
Typ/
Min
Temp Tensile
Strength
Yield
Strength
(0.5% ext.
under load)
Yield
Strength
(0.2%
offset)
Yield
Strength
(0.05%
offset)
El Rockwell
Hardness
Vickens
Hard.
Brinell
Hard.
Shear
Strength
Fatigue
Strength*
Izod
Impact
Strength

in. %
F ksi ksi ksi ksi % B C F 30T 500 500 3000 ksi ksi ft-lb

mm.

C MPa MPa MPa MPa







MPa MPa J
As Sand Cast
M010.00TYP684521--30-----70---0.0

0.0

20310145--30-----70---0.0
As Centrifugal Cast
M020.00TYP684521--30-----70---0.0

0.0

20310145--30-----70---0.0
M020.00SMIN684018--20---------0.0

0.0

20275125--20---------0.0
As Continuous Cast
M070.00SMIN684422--18---------0.0

0.0

20303152--18---------0.0
As Sand Cast
M010.00SMIN684018--20---------0.0

0.0

20276124--20---------0.0

*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.



APPLICABLE SPECIFICATIONS:

NOTE: Information courtesy of Copper.org
ProductSpecification
CentrifugalASTM B271
SAE J462, J461
ContinuousASTM B505
SAE J462, J461
IngotASTM B30
PrecisionMILITARY MIL-C-11866
SandASTM B763, B584
SAE J461, J462