Home > BRONZE > Bronze - Cast Alloys > C86300 > C86300 Solid Bar
We found 0 results matching your criteria.

C86300 Manganese Bronze Solid Bar


Atlas Bronze offers
C86300 Solid Bar Manganese Bronze. C86300 Solid Bar is available as Continuous Cast Bar Stock per ASTM B505 in Standard Sizes (see below) or special mill runs depending on the total quantity that your project requires.

Manganese bronze is not used in the commercial or consumer market; it is found almost exclusively in the industrial sector. This is because of the durability and toughness of manganese bronze. It is used to make bushings, valve stems, hydraulic cylinder components and propellers. Its primary use in industry means this bronze is typically sold in large amounts, with a standard bar length of 144 inches or 12 feet.

__________________________________________________________________________________________






Diameter (inches)Part Number
0.750"8630S-6
1.000"8630S-8
1.250"8630S-10
1.500"8630S-12
1.750"8630S-14
2.000"8630S-16
2.500"8630S-20
2.750"8630S-22
3.000"8630S-24
3.500"8630S-28
4.000"8630S-32
4.500"8630S-36
4.750"8630S-38
5.000"8630S-40
5.500"8630S-44
6.000"8630S-48
6.500"8630S-52
7.000"8630S-56
7.125"8630S-57
7.500"8630S-60
8.000"8630S-64
9.000"8630S-72
10.00"8630S-80
11.00"8630S-88
12.00"8630S-96
13.00"8630S-104
__________________________________________________________________________________________


TYPICALLY USED FOR:


This material is used in a variety of applications. Typical uses for this alloy are: Extra heavy duty, high strength alloy. Large valve stems, gears, cams, slow-speed heavy-load bearings, screwdown nuts hydraulic cylinder parts.


CHEMICAL COMPOSITION:

(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
Cu(1) Al Fe Pb Mn Ni(2) Sn Zn
Min./Max. 60.0-66.0 5.0-7.5 2.0-4.0 .20 2.5-5.0 1.0 .20 22.0-28.0
Nominal 63.0 6.2 3.0 - 3.7 - - 25.0
(1) In determining Cu min., Cu may be calculated as Cu + Ni.
(2) Ni value includes Co.
Note: Cu + Sum of Named Elements, 99.0% min.



MECHANICAL PROPERTIES:

NOTE: Information courtesy of Copper.org
Temper Section
Size
Cold
Work
Typ/
Min
Temp Tensile
Strength
Yield
Strength
(0.5% ext.
under load)
Yield
Strength
(0.2%
offset)
Yield
Strength
(0.05%
offset)
El Rockwell
Hardness
Vickens
Hard.
Brinell
Hard.
Shear
Strength
Fatigue
Strength*
Izod
Impact
Strength

in. %
F ksi ksi ksi ksi % B C F 30T 500 500 3000 ksi ksi ft-lb

mm.

C MPa MPa MPa MPa







MPa MPa J
As Sand Cast
M01 0.0 0 TYP 68 119 62 - - 18 - - - - - - 225 - 25 15.0

0.0

20 821 427 - - 18 - - - - - - 225 - 172 20.0
As Centrifugal Cast
M02 0.0 0 SMIN 68 110 60 - - 12 - - - - - - - - - 0.0

0.0

20 758 414 - - 12 - - - - - - - - - 0.0
As Continuous Cast
M07 0.0 0 SMIN 68 110 62 - - 14 - - - - - - - - - 0.0

0.0

20 758 427 - - 14 - - - - - - - - - 0.0
As Sand Cast
M01 0.0 0 SMIN 68 110 60 - - 12 - - - - - - 223 - - 0.0

0.0

20 760 415 - - 12 - - - - - - 223 - - 0.0

*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.



APPLICABLE SPECIFICATIONS:

NOTE: Information courtesy of