Home > BRONZE > Bronze - Cast Alloys > C86300 > C86300 Rectangle
We found 0 results matching your criteria.

C86300 Manganese Bronze Rectangle / Plate

Atlas Bronze offers
C86300 Rectangle / Plate Manganese Bronze. C86300 Rectangle / Plate is available as Continuous Cast Bar Stock per ASTM B505 and Sand Castings per ASTM B584. The method in which the material is cast will depend on your size, specification and desired quantity.


C86300 Rectangle / Plate is in Standard thicknesses or we can cut your desired thickness, width and length from one of our Big Blocks! We regularly stock our C86300 Big Block Plates in a variety of sizes to achieve optimal cutting capacity:

  • 4" thick x 15" wide
  • 5" thick x 15" wide
  • 8" thick x 18" wide
  • 10" thick x 12" wide



Manganese bronze is not used in the commercial or consumer market; it is found almost exclusively in the industrial sector. This is because of the durability and toughness of manganese bronze. It is used to make bushings, valve stems, hydraulic cylinder components and propellers. Its primary use in industry means this bronze is typically sold in large amounts, with a standard bar length of 144 inches or 12 feet.

__________________________________________________________________________________________






Thickness (inches)
Part Number
0.2500" 8630R-2
0.3750" 8630R-3
0.5000" 8630R-4
0.6250" 8630R-5
0.7500" 8630R-6
1.0000" 8630R-8
1.2500" 8630R-10
1.3750" 8630R-11
1.5000" 8630R-12
1.6250" 8630R-13
1.7500" 8630R-14
2.0000" 8630R-16
__________________________________________________________________________________________


TYPICALLY USED FOR:


This material is used in a variety of applications. Typical uses for this alloy are: Extra heavy duty, high strength alloy. Large valve stems, gears, cams, slow-speed heavy-load bearings, screwdown nuts hydraulic cylinder parts.


CHEMICAL COMPOSITION:

(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
Cu(1) Al Fe Pb Mn Ni(2) Sn Zn
Min./Max. 60.0-66.0 5.0-7.5 2.0-4.0 .20 2.5-5.0 1.0 .20 22.0-28.0
Nominal 63.0 6.2 3.0 - 3.7 - - 25.0
(1) In determining Cu min., Cu may be calculated as Cu + Ni.
(2) Ni value includes Co.
Note: Cu + Sum of Named Elements, 99.0% min.



MECHANICAL PROPERTIES:

NOTE: Information courtesy of Copper.org
Temper Section
Size
Cold
Work
Typ/
Min
Temp Tensile
Strength
Yield
Strength
(0.5% ext.
under load)
Yield
Strength
(0.2%
offset)
Yield
Strength
(0.05%
offset)
El Rockwell
Hardness
Vickens
Hard.
Brinell
Hard.
Shear
Strength
Fatigue
Strength*
Izod
Impact
Strength

in. %
F ksi ksi ksi ksi % B C F 30T 500 500 3000 ksi ksi ft-lb

mm.

C MPa MPa MPa MPa







MPa MPa J
As Sand Cast
M01 0.0 0 TYP 68 119 62 - - 18 - - - - - - 225 - 25 15.0

0.0

20 821 427 - - 18 - - - - - - 225 - 172 20.0
As Centrifugal Cast
M02 0.0 0 SMIN 68 110 60 - - 12 - - - - - - - - - 0.0

0.0

20 758 414 - - 12 - - - - - - - - - 0.0
As Continuous Cast
M07 0.0 0 SMIN 68 110 62 - - 14 - - - - - - - - - 0.0

0.0

20 758 427 - - 14 - - - - - - - - - 0.0
As Sand Cast
M01 0.0 0 SMIN 68 110 60 - - 12 - - - - - - 223 - - 0.0

0.0

20 760 415 - - 12 - - - - - - 223 - - 0.0

*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.



APPLICABLE SPECIFICATIONS:

NOTE: Information courtesy of Copper.org
Product Specification
Centrifugal AMS 4862
ASTM B271
SAE J462, J461
Continuous ASTM B505
Ingot ASTM B30
FEDERAL QQ-C-523
Precision MILITARY MIL-C-11866
Sand AMS 4862
ASTM B763, B584, B22
SAE J462, J461