Atlas Bronze offers C83600 Leaded Red Brass, SAE 40 in number of sizes & shapes. Click your desired shape below and explore our range. If you do not see what you are looking for please contact us with your requirements and we would be more than happy to assist.
__________________________________________________________________________________________
Click on the below image to select your size:
 
__________________________________________________________________________________________
TYPICALLY USED FOR:
This material is used in a variety of applications. Typical uses for this alloys are: Valves, flanges, pipe fittings, plumbing goods, pump castings, water
pump impellers and housings, ornamental fixtures small gears.
CHEMICAL COMPOSITION:
(%max., unless shown as range or min.)
NOTE: Information courtesy of Copper.org
| |
Cu(1) | Al | Sb | Fe | Pb | Ni(2) | P(3) | Si | S | Sn | Zn |
|---|
| Min./Max. | 84.0-86.0 | .005 | .25 | .30 | 4.0-6.0 | 1.0 | .05 | .005 | .08 | 4.0-6.0 | 4.0-6.0 | | Nominal | 85.0 | - | - | - | 5.0 | - | - | - | - | 5.0 | 5.0 |
(1) In determining Cu min., Cu may be calculated as Cu + Ni.
(2) Ni value includes Co.
(3) For continuous castings, P shall be 1.5%, max.
Note: Cu + Sum of Named Elements, 99.3% min.
NOTE: Information courtesy of Copper.org
MECHANICAL PROPERTIES:
(measured at room temperature, 68 F (20 C)
NOTE: Information courtesy of Copper.org
| Temper |
Section
Size |
Cold
Work |
Typ/
Min |
Temp |
Tensile
Strength |
Yield
Strength
(0.5% ext.
under load) |
Yield
Strength
(0.2%
offset) |
Yield
Strength
(0.05%
offset) |
El |
Rockwell
Hardness |
Vickens
Hard. |
Brinell
Hard. |
Shear
Strength |
Fatigue
Strength* |
Izod
Impact
Strength |
|---|
| in. |
% |
| F |
ksi |
ksi |
ksi |
ksi |
% |
B |
C |
F |
30T |
500 |
500 |
3000 |
ksi |
ksi |
ft-lb |
| mm. |
|
| C |
MPa |
MPa |
MPa |
MPa |
|
|
|
|
|
|
|
|
MPa |
MPa |
J |
| As Sand Cast | | M01 | 0.0 | 0 | TYP | 68 | 37 | 17 | - | - | 30 | - | - | - | - | - | 60 | - | - | 11 | 10.0 |
| 0.0 |
|
| 20 | 255 | 117 | - | - | 30 | - | - | - | - | - | 60 | - | - | 76 | 14.0 | | As Centrifugal Cast | | M02 | 0.0 | 0 | SMIN | 68 | 30 | 14 | - | - | 20 | - | - | - | - | - | - | - | - | - | 0.0 |
| 0.0 |
|
| 20 | 207 | 97 | - | - | 20 | - | - | - | - | - | - | - | - | - | 0.0 | | As Continuous Cast | | M07 | 0.0 | 0 | SMIN | 68 | 36 | 19 | - | - | 15 | - | - | - | - | - | - | - | - | - | 0.0 |
| 0.0 |
|
| 20 | 248 | 131 | - | - | 15 | - | - | - | - | - | - | - | - | - | 0.0 | | As Sand Cast | | M01 | 0.0 | 0 | SMIN | 68 | 30 | 14 | - | - | 20 | - | - | - | - | - | - | - | - | - | 0.0 |
| 0.0 |
|
| 20 | 205 | 97 | - | - | 20 | - | - | - | - | - | - | - | - | - | 0.0 |
APPLICABLE SPECIFICATIONS:
NOTE: Information courtesy of Copper.org
| Product | Specification |
| Centrifugal | AMS 4855
ASTM B271
SAE J462, J461 | | Continuous | ASTM B505
SAE J462, J461 | | Fittings | ASME B16.15, SB62, B16.32, B16.26, B16.23, B16.18
ASTM B62
FEDERAL WW-P-460 | | Flanges | ASME SB62, B16.24
ASTM B62 | | Ingot | ASTM B30 | | Precision | MILITARY MIL-C-11866 | | Sand | AMS 4855
ASME SB62
ASTM B584, B62
SAE J461, J462
| | Unions | FEDERAL WW-U-516
|
|
|
|
