Atlas carries C63000 Nickel Aluminum Bronze in
Solid Bar & Plate stock. We carry a very large range of sizes and will cut the
material to length. C63000 is a special high-strength aluminum bronze
used in applications involving heavy loads, friction, and abrasive wear and
corrosion. The addition of nickel increases the alloys strength without
reducing its excellent ductility, toughness, and good wear resistance.
__________________________________________________________________________________________
Click on the below image to select your size:
 
__________________________________________________________________________________________
TYPICAL USES:
Some of the typical areas that C63000 is used in, is as follows: Valve Seats, Plunger Tips, Condenser Tube for Power Stations and
Desalting Units, Shafting, Pump Parts, Cams, Gears, Valve Guides,
Aircraft Parts, Pump Shafts, Structural Members, Corrosion Resistant
Articles, Hydraulic Bushings for Earth Moving Equipment, Valve Balls,
Bushings, Bearings, Heat Exchanger Flanges, Heat Exchanger Headers,
Tanks, Welded Piping Systems, Balls
CHEMICAL COMPOSITION:
(%max., unless shown as range or min.)
| |
Cu(1) | Al | Fe | Mn | Ni(2) | Si | Sn | Zn |
|---|
| Min./Max. | Rem. | 9.0-11.0 | 2.0-4.0 | 1.5 | 4.0-5.5 | .25 | .20 | .30 | | Nominal | 82.0 | 10.0 | 3.0 | - | 5.0 | - | - | - |
(1) Cu value includes Ag.
(2) Ni value includes Co.
Note: Cu + Sum of Named Elements, 99.5% min.
MECHANICAL PROPERTIES:
(measured at room temperature, 68 F (20 C)
| Temper |
Section
Size |
Cold
Work |
Typ/
Min |
Temp |
Tensile
Strength |
Yield
Strength
(0.5% ext.
under load) |
Yield
Strength
(0.2%
offset) |
Yield
Strength
(0.05%
offset) |
El |
Rockwell
Hardness |
Vickens
Hard. |
Brinell
Hard. |
Shear
Strength |
Fatigue
Strength* |
Izod
Impact
Strength |
|---|
| in. |
% |
| F |
ksi |
ksi |
ksi |
ksi |
% |
B |
C |
F |
30T |
500 |
500 |
3000 |
ksi |
ksi |
ft-lb |
| mm. |
|
| C |
MPa |
MPa |
MPa |
MPa |
|
|
|
|
|
|
|
|
MPa |
MPa |
J |
| Rod | | M30 | 4 | 0 | TYP | 68 | 100 | 60 | - | - | 15 | 96 | - | - | - | - | - | - | 62 | 36 | 0.0 |
| 102 |
|
| 20 | 689 | 414 | - | - | 15 | 96 | - | - | - | - | - | - | 427 | 248 | 0.0 | | Bar | | HR50 | 2 | 10 | TYP | 68 | 100 | 60 | - | - | 15 | 96 | - | - | - | - | - | - | - | - | 0.0 |
| 51 |
|
| 20 | 689 | 414 | - | - | 15 | 96 | - | - | - | - | - | - | - | - | 0.0 | | Rod | | HR50 | 3 | 10 | TYP | 68 | 112 | 62 | - | - | 20 | 96 | - | - | - | - | - | - | 65 | 37 | 0.0 |
| 76 |
|
| 20 | 772 | 427 | - | - | 20 | 96 | - | - | - | - | - | - | 448 | 255 | 0.0 | | Bar | | M30 | 3 | 0 | TYP | 68 | 90 | 50 | - | - | 15 | 96 | - | - | - | - | - | - | - | - | 0.0 |
| 76 |
|
| 20 | 621 | 345 | - | - | 15 | 96 | - | - | - | - | - | - | - | - | 0.0 | | Rod | | HR50 | 1 | 10 | TYP | 68 | 118 | 75 | - | - | 15 | 98 | - | - | - | - | - | - | 70 | 37 | 0.0 |
| 25.4 |
|
| 20 | 814 | 517 | - | - | 15 | 98 | - | - | - | - | - | - | 483 | 255 | 0.0 | | Bar | | HR50 | 1 | 10 | TYP | 68 | 110 | 62 | - | - | 15 | 97 | - | - | - | - | - | - | - | - | 0.0 |
| 25.4 |
|
| 20 | 758 | 427 | - | - | 15 | 97 | - | - | - | - | - | - | - | - | 0.0 | | Rod | | HR50 | 2 | 10 | TYP | 68 | 115 | 65 | - | - | 18 | 96 | - | - | - | - | - | - | 69 | 38 | 0.0 |
| 51 |
|
| 20 | 793 | 448 | - | - | 18 | 96 | - | - | - | - | - | - | 476 | 262 | 0.0 |
*Fatigue Strength: 100 x 10 6cycles,
unless indicated as [N]X 106.
APPLICABLE SPECIFICATIONS:
| Product | Specification |
| Bar | AMS 4640
ASME SB150
ASTM B150
FEDERAL QQ-C-450
SAE J463, J461 | | Bar, Forging | ASTM B124 | | Bolts | ASTM F468 | | Forgings, Die | AMS 4640
ASTM B283
MILITARY MIL-B-16166 | | Nuts | ASTM F467 | | Plate | ASTM B171
FEDERAL QQ-C-450 | | Plate, Condenser Tube | ASME SB171
ASTM B171 | | Rod | AMS 4640
ASME SB150
ASTM B150
SAE J463, J461 | | Rod, Forging | ASTM B124 | | Screws | ASTM F468 | | Shapes | AMS 4640
ASTM B150
SAE J461, J463 | | Shapes, Forging | ASTM B124 | | Sheet | FEDERAL QQ-C-450 | | Strip | FEDERAL QQ-C-450 | | Tube | AMS 4640 |
|
